Once upon a time televisions were mostly made up of tubes encased in wood, wires, knobs, scanners, and rabbit ears. As with most things, televisions have become much more complicated and technical in today's world. Even though you may not have any plans to become a television repair person, you might still be interested in learning about the boards, such as the T-Con d50ud1, inside LCD tvs, if the science of electronics intrigues you.
If you open up the back of your television set you will probably find the power supply board, or power supply module, on the right hand side of your unit as you are looking at it. It will be the largest and heaviest of all the boards on the back of the set. The purpose of this board is to convert the AC, or alternating current, supply, which can change directions, into DC, or direct current, voltage.
Direct current moves in one direction only and is what the circuit inside the LCD television uses. In some televisions the power supply board and the inverter board are joined together. If the power supply board malfunctions you'll get no power or intermittent power.
The T-Con, or timing control board, will be the smallest board on the panel. LCD televisions are the only ones that have them. These boards are usually covered by a shield and are located on the top back of your panel.
The T-Con board is there to control the TFT, thin film transistor, driver and the circuit. If you're experiencing horizontal or vertical lines you may be having trouble with the timing control board. Other indications are a white screen, a double image, or no image at all.
You will find the inverter board at the back along the television's edge. If you have any tv other than an LCD, there will be no inverter board. This board is on the tv in order to convert the low voltage direct current, that the switched mode power supplies, into high voltage alternate current. Backlights are lit up with this. Inverters boards are sometimes combined with power boards. If your inverter board goes bad, you may see a dim screen or a display that shuts down entirely.
The main board is also called the main module, the digital or logic board, or the motherboard. The video and audio inputs and outputs are attached to it. The main board converts signals from analog to digital. If you're having trouble with the sound or the color, it may be the main board.
Sometimes the audio receiving or jackpack board is separated from the mother board. The jackpack takes the sound signal to the processor and moves it to the amplifier. The amplifier drives the speakers located on both sides of the television. The jackpack may be your problem if you experience no sound, high pitched sound, or channels that randomly change.
If you open up the back of your television set you will probably find the power supply board, or power supply module, on the right hand side of your unit as you are looking at it. It will be the largest and heaviest of all the boards on the back of the set. The purpose of this board is to convert the AC, or alternating current, supply, which can change directions, into DC, or direct current, voltage.
Direct current moves in one direction only and is what the circuit inside the LCD television uses. In some televisions the power supply board and the inverter board are joined together. If the power supply board malfunctions you'll get no power or intermittent power.
The T-Con, or timing control board, will be the smallest board on the panel. LCD televisions are the only ones that have them. These boards are usually covered by a shield and are located on the top back of your panel.
The T-Con board is there to control the TFT, thin film transistor, driver and the circuit. If you're experiencing horizontal or vertical lines you may be having trouble with the timing control board. Other indications are a white screen, a double image, or no image at all.
You will find the inverter board at the back along the television's edge. If you have any tv other than an LCD, there will be no inverter board. This board is on the tv in order to convert the low voltage direct current, that the switched mode power supplies, into high voltage alternate current. Backlights are lit up with this. Inverters boards are sometimes combined with power boards. If your inverter board goes bad, you may see a dim screen or a display that shuts down entirely.
The main board is also called the main module, the digital or logic board, or the motherboard. The video and audio inputs and outputs are attached to it. The main board converts signals from analog to digital. If you're having trouble with the sound or the color, it may be the main board.
Sometimes the audio receiving or jackpack board is separated from the mother board. The jackpack takes the sound signal to the processor and moves it to the amplifier. The amplifier drives the speakers located on both sides of the television. The jackpack may be your problem if you experience no sound, high pitched sound, or channels that randomly change.
About the Author:
See the featured products including the d50ud1 by referring to the Web. Spend a minute or two browsing the online store at http://www.tekbyus.com/product-tag/d50u-d1.
0 comments:
Post a Comment
Please give your comments here!