There are a number of reasons why you might want to do a repair. One of it is that your television may be powering off on its own or it may take a long duration to get reception as soon as it is turned on. Lucky enough, this kind of issue can be solved by TV power supply repair. Before beginning, below are some of the crucial steps you need to look into.
There are a number of tools you will need to effectively do the job. They include a capacitor, soldering iron, solder, screwdriver and a solder sucker. Confirm that your toolbox has all these items, and if not, you will have to go to the store. You should first determine if the problem is really what you want to repair. In television electric supplies, capacitors normally go bad causing them to leak and bulge hence the monitor will not get power.
Once the television has been unplugged from its power source, ensure you place it on a flat area with the screen facing down to prevent any damages. You can then detach all screws that have attached the back panel with a screwdriver. After all of them have been removed, you can detach the back panel by wiggling it a little bit since it is not secured with bolts and then keep it aside.
The next step is to locate where the circuit board is by following the board that the power cord is linked to. Disconnect the screws and connectors by using a screwdriver from the board. Ensure you note where they all came from as you will have to reattach them as they were. It is imperative you take pictures so that you do not get confused during reattaching. After the connectors and screws are unattached, remove the circuit board.
Check to see the capacitors that are malfunctioning. Capacitors assume the shape of tiny cylinders and only vary in their length and width. Since most of them may appear normal, search for those that have bulged at the surface or are removing a brownish to yellowish liquid on the surface. This means that they have been overheated leading to the problem you are facing. Make sure that no damage is done to copper pads when removing them.
After all of the bad ones have been gotten rid of, replacement with new ones ought to be done. Make sure you note the positive and negative polarity while doing the replacement. Mark negative leads using a soldering iron on the board. The negative side normally has a stripe colored in gray. The capacitors need to be correctly installed since they are polarity complex.
Reassemble the device and the check power. After replacing connectors, back panel and screws, confirm whether the issue has been resolved. A power surge probably may have caused the fuse to blow. If the problem is not yet resolved, test the fuse. You will have to look for the appropriate fuse and replace it with the old one.
If none of these solves the problem, your last option is to replace the main circuit board of the device. This is because if it is damaged, the television would not work correctly. Before doing this, you should have guidance on how it should be replaced so that you do not cause further damage to the device.
There are a number of tools you will need to effectively do the job. They include a capacitor, soldering iron, solder, screwdriver and a solder sucker. Confirm that your toolbox has all these items, and if not, you will have to go to the store. You should first determine if the problem is really what you want to repair. In television electric supplies, capacitors normally go bad causing them to leak and bulge hence the monitor will not get power.
Once the television has been unplugged from its power source, ensure you place it on a flat area with the screen facing down to prevent any damages. You can then detach all screws that have attached the back panel with a screwdriver. After all of them have been removed, you can detach the back panel by wiggling it a little bit since it is not secured with bolts and then keep it aside.
The next step is to locate where the circuit board is by following the board that the power cord is linked to. Disconnect the screws and connectors by using a screwdriver from the board. Ensure you note where they all came from as you will have to reattach them as they were. It is imperative you take pictures so that you do not get confused during reattaching. After the connectors and screws are unattached, remove the circuit board.
Check to see the capacitors that are malfunctioning. Capacitors assume the shape of tiny cylinders and only vary in their length and width. Since most of them may appear normal, search for those that have bulged at the surface or are removing a brownish to yellowish liquid on the surface. This means that they have been overheated leading to the problem you are facing. Make sure that no damage is done to copper pads when removing them.
After all of the bad ones have been gotten rid of, replacement with new ones ought to be done. Make sure you note the positive and negative polarity while doing the replacement. Mark negative leads using a soldering iron on the board. The negative side normally has a stripe colored in gray. The capacitors need to be correctly installed since they are polarity complex.
Reassemble the device and the check power. After replacing connectors, back panel and screws, confirm whether the issue has been resolved. A power surge probably may have caused the fuse to blow. If the problem is not yet resolved, test the fuse. You will have to look for the appropriate fuse and replace it with the old one.
If none of these solves the problem, your last option is to replace the main circuit board of the device. This is because if it is damaged, the television would not work correctly. Before doing this, you should have guidance on how it should be replaced so that you do not cause further damage to the device.
About the Author:
To help you get your TV power supply, simply go to our online page for details. You will find all the relevant information by clicking here http://www.tekbyus.com.
0 comments:
Post a Comment
Please give your comments here!